pcs
Also notice our alternatives
Our alternatives (similar item) This is based on our general assessment. Please check that the item is suitable for your special operating case. If in doubt, please ask us for advice.
Immediately available
You are not logged in. The availability display refers therefore to 1 pcs. Log in to have the availability of the requested quantity displayed.
Properties
Po­si­tion drive di­men­sions 0090
Flange drilling screen F07,
F10
Swivel angle [deg] 90
Ad­justable range end po­si­tion at 0° [deg] -1 to 9
Shaft con­nec­tion Depth [mm] 24,8
Stan­dard con­nec­tion to fit­ting ISO 5211
Damp­en­ing No damp­en­ing
in­stal­la­tion po­si­tion ar­bi­trary
Prin­ci­ple of op­er­a­tion sin­gle ac­tion
Con­struc­tion set up Joch kine­mat­ics
Po­si­tion de­tec­tion with­out
Clos­ing di­rec­tion Right clos­ing
Valve con­nec­tion cor­re­sponds to stan­dard VDI/VDE 3845 (NAMUR)
Safety In­tegrity Level (SIL) Prod­uct can be used in SRP/CS up to SIL 2 Low De­mand,
Prod­uct can be used in SRP/CS up to SIL 2 High De­mand
Op­er­at­ing pres­sure [bar] 3.5 to 8.4
Nom­i­nal op­er­at­ing pres­sure [bar] 5,6
CE cer­tifi­cate (see de­c­la­ra­tion of con­for­mity) to EU EX pro­tec­tion di­rec­tive (ATEX)
ATEX gas cat­e­gory II 2G
ATEX dust cat­e­gory II 2D
Ex ig­ni­tion pro­tec­tion type gas Ex h IIC T6...T3 Gb X
Ex ig­ni­tion pro­tec­tion type dust Ex h IIIC T85°C...T200°C Db X
Ex am­bi­ent tem­per­a­ture -20°C <= Ta <= +60°C
Op­er­at­ing medium Com­pressed air to ISO 8573-​1:2010 [7:4:4]
In­for­ma­tion about op­er­at­ing and con­trol medium Oiled op­er­a­tion pos­si­ble (re­quired in fur­ther op­er­a­tions)
Cor­ro­sion re­sis­tant class KBK 3 - se­vere cor­ro­sion stress
am­bi­ent tem­per­a­ture [°C] -20 to 80
Ro­tary torque for nom­i­nal op­er­at­ing pres­sure and 0° pivot angle [Nm] 112,6
Ro­tary torque for nom­i­nal op­er­at­ing pres­sure and 50° pivot angle [Nm] 61,9
Ro­tary torque for nom­i­nal op­er­at­ing pres­sure and 90° pivot angle [Nm] 93,8
In­for­ma­tion about torque The op­er­at­ing torque of the ac­tu­a­tor may not be higher than the max­i­mum per­mit­ted torque listed in ISO 5211, re­lated to the size of the fas­ten­ing flange and the cou­pling.
Air con­sump­tion a 6 bar per cycle 0°-90°-0° [LTR] 3,85
Prod­uct weight [g] 5.900
Shaft con­nec­tion T22
Pneu­matic con­nec­tion G1/8
Ma­te­r­ial in­for­ma­tion RoHs com­pli­ant
Cover ma­te­r­ial Alu­minium wrought alloy
Seals ma­te­r­ial FKM,
NBR,
PUR
Hous­ing ma­te­r­ial Alu­minium wrought alloy
Screws ma­te­r­ial High-​alloyed steel
Shaft ma­te­r­ial High-​alloyed steel
Ma­te­r­ial num­ber shaft 1.4305
Ad­justable range end po­si­tion at 90° [deg] 81 to 91
In­for­ma­tion about the ad­just­ment range of the end po­si­tions Se­lec­tively one end po­si­tion is ad­justable
Con­nec­tion pres­sure for spring strength [bar] 3,5
Spring force torque at a swivel angle 0° [Nm] 37,5
Spring force torque at a swivel angle 50° [Nm] 28,1
Spring force torque at 90° [Nm] 56,3
Spring strength 2
Further information on OT-FESTO004321
Weight 5.900 g / pcs
Customs duty number 84123900
Manufacturer Festo
Documents

 
All data are to be understood as non-binding reference values! We do not assume liability for any data selection not confirmed in writing. Unless otherwise specified, pressure values refer to liquids from Group II at +20°C.
deliverable again in ⌀ 3 weeks
Late ordering service
21 min left

When you place an order online Monday - Thursday from 16:30 - 21:00, or on Friday from 16:30 - 18:00, we will ship your order on request on the same day by GLS (charge: 5%, min. € 10,00).